Once that is done you can upgrade the device firmware, and begin configuring your network under Settings and remember to set a monthly schedule for auto firmware updates.The device will receive its new configuration from the UniFi Cloud Controller and reboot, afterwards the status should change to “Connected”.The device status should change from “Pending” to “Adopting”, and then “Provisioning” fairly quickly.You should notice your new devices will now show up for adoption on ALL sites in your UniFi Cloud Controller, use the sites drop down in the upper right corner to switch to the site you want the device to be adopted in, then click “Adopt” Log into your Unifi Cloud Controller and create your new site if needed.Make sure to use instead of and use :8080/inform, at the end of the domain, example.Make sure to use a DNS name instead of an IP address.In that same console window type without quotes “ set-inform” followed by the server address.Login using the default username is ubnt and password is ubnt.Enter the IP address of the UniFi device, Port 22, Connection type: SSH, and click “Open”.Within Advanced IP Scanner make sure to notice the IP addresses that each Unifi Device is using.Choose Windows PowerShell Connect SSH Type ssh ubnt192.168.1.142 (replace 192.168.1. Note: Make sure network discovery is enabled on your computer Press Windows key + X (or right-click your start menu) 2.Using putty to access this IP address and the default port 22 selected in putty I can get to the enter username and password part. I found the directions to ssh into the controller ( 10.13.80.1 ) on the default site. Open the Advanced IP Scanner and run a scan to locate all your New Unifi devices. I think I have the set inform url wrong on the second site (controller on default site). Download and install Advanced IP Scanner.So I believe this is the most straight forward method.In this Tutorial I will be showing you how to adopt New Unifi Devices to your Unifi Cloud Controller using the SSH Method. `8443` and `8080` are both on the allowed ports for Cloudflare, but without a tunnel that would require opening the ports and pointing the subdomain at your public IP address (something I pondered with Duck DNS before deciding to try this first). If someone has another, perhaps cleaner solution, I'm all ears. But it's the same concept.Įnd result is I now have: :8443 and :8080 both going to the same internal IP. He uses it for a totally different internal application. So maybe it is possible using a different method.īut the solution I found after rewatching DB Tech ( I recall seeing multiple Cloudflare tunnel tutorials on channels I watch recently, but this one was the first I rediscovered) was to simply create a second subdomain with `:8080` and things seem to be working. I recall trying to manually set up tunnels with the command line last year and failing. So when you try to go to ` :8080/inform` you just get a redirect and attempt to access the machine on `8443`. However the subdomain you set up in Zero Trust usually includes the port when filling out the "setup wizard." There's no way to add other ports to the same subdomain in the interface. It's not too difficult to set up a tunnel allowing access to the machine where your Unifi controller is located internally. I tried adopting e from the Unifi Console additionally it fails, i done advanced adoption from device username and password both it misses. SSH into it and set-inform go console address. I found this post while dealing with what I believe is the same issue. The Set-Inform URL tells the Unifi Access Point where the controller be located. The inform URL is the IP Mailing of your console followed the the port number: 8080/inform. (or lookup and SSH details in your controller) Set-Inform URL. The set-inform process is a required step in adopting your devices to the Cloud. This Set-Inform URL tells to Unifi Access Point where the controller will located. If i log into the unify and type help i see. This will allow you to then check the device information, upgrade the firmware, reset the device, and set the controller URL as the inform target. I am reading conflicting ways to reset the unifi to factory default and also set the inform url both via SSH. To give some clarity to the first two responses and hopefully provide a solution. you will first need to establish an SSH connection to the device.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |